Free Stampin' Up! PDF Tutorial for 3D Teepee Fun Fold Christmas card
Stampin' Up! Christmas 2020 shaker card using In The Pines bundle.

2020 Christmas Gift Card Holder using Stampin' Up! Poinsettia Petals and Quite Curvy Bundle

Hello friends. Today I have step by step instructions to make a gift card holder from half a sheet of A4 cardstock. I have used Stampin' Up! Poinsettia Petals bundle for the decoration, and a brand new bundle called Quite Curvy for the die cutting on the gift card holder. This Quite Curvy bundle will be in the Stampin' Up! 2021 January to June Mini Catalogue, but is being released early and will be available for customers to purchase from next Tuesday, 3rd November.

DIY gift card holder step by step instructions with pictures. Uses Stampin Up Poinsettia Petals and Quite Curvy Bundles. Made by Claire Daly Stampin Up Demonstrator Melbourne Australia

Step by Step Instructions

1. Start with a piece of A4 Gray Granite Cardstock, which is cut down the centre vertically.

2. Score from right to left at 8cm and 20cm

DIY gift card holder step by step instructions with pictures. Uses Stampin Up Poinsettia Petals and Quite Curvy Bundles. Made by Claire Daly Stampin Up Demonstrator Melbourne Australia

3. On the 8cm end (at the right) use a circle punch (I used this 2" circle punch) to cut a semi circle in the end.

DIY gift card holder step by step instructions with pictures. Uses Stampin Up Poinsettia Petals and Quite Curvy Bundles. Made by Claire Daly Stampin Up Demonstrator Melbourne Australia

4. Add two strips of strong adhesive (like Stampin' Up! Tear and Tape) to the inside edges of this piece. This adhesive is recommended for boxes and 3D items as it sticks really well.

DIY gift card holder step by step instructions with pictures. Uses Stampin Up Poinsettia Petals and Quite Curvy Bundles. Made by Claire Daly Stampin Up Demonstrator Melbourne Australia

5. This then folds up to make the slot to place the gift card. 

6. Stamp a sentiment in the bottom right hand corner of the folded up piece (this will also show when the gift card holder is closed. My sentiment is from Wrapped in Christmas stamp set, and I stamped in Gray Granite ink.

DIY gift card holder step by step instructions with pictures. Uses Stampin Up Poinsettia Petals and Quite Curvy Bundles. Made by Claire Daly Stampin Up Demonstrator Melbourne Australia

7. Add a piece of coordinating patterned paper to the top flap (I used a piece of Gray Granite patterned paper from the Neutrals 6x6" patterned paper stack) and die cut the edge with one of the new Curvy Dies (or any other decorative edging die or punch you have). I actually did mine separately but I think adhering the patterned paper on first would have been easier. When you die cut, make sure you do it high enough up so that the sentiment will be visible (but not any of the semi circle cutaway).

DIY gift card holder step by step instructions with pictures. Uses Stampin Up Poinsettia Petals and Quite Curvy Bundles. Made by Claire Daly Stampin Up Demonstrator Melbourne Australia

8.  For the belly band, cut a strip of Blackberry Bliss cardstock 3.5cm wide, and the length of a piece of A4 cardstock (29.7cm). Cut coordinating DSP the same length but only 3.3cm wide. Adhere the patterned paper to the cardstock strip. If you are joining strips of patterned paper (as I had to) to complete the length, make sure the joins aren't in the middle area, so they wont be seen on the front. I started with a strip of paper in the middle and then added at either end to ensure this.

9. Loosely fold the belly band around the gift card holder and secure with Tear and Tape at the back.

10. Add several layers of linen thread around the belly band and tie at the back. I gathered these together under where the flower was going to be and secured with a piece of tape. I then fanned the threads out a bit at the top and bottom.

DIY gift card holder step by step instructions with pictures. Uses Stampin Up Poinsettia Petals and Quite Curvy Bundles. Made by Claire Daly Stampin Up Demonstrator Melbourne Australia

11. The flower was watercoloured in the same way as I did the flower in THIS post, except I used Melon Mambo and Blackberry Bliss reinkers this time, and only used Blackberry Bliss die cut foliage.

12. The flower is attached using Stampin' Dimensionals and I have coloured the clear Rhinestone jewells in the centre of the flower using my light Blackberry Bliss Stampin' Blends marker.

DIY gift card holder step by step instructions with pictures. Uses Stampin Up Poinsettia Petals and Quite Curvy Bundles. Made by Claire Daly Stampin Up Demonstrator Melbourne Australia

There you have it! I hope you have lots of fun making up your very own Gift Card Holder. Friends and family would be wowed to receive a gift card in a holder like this at Christmas.

Get Free Weekly PDF Tutorials From Me

If you loved this project, sign up to get a weekly free project tutorial designed by me, and sent to your email each weekend.

Join my Subscriber Community for a free PDF Tutorial every week.

or Subscribe to receive all my Blog Posts by Email

Shutterstock_1456013552

You can find all the products I have used today in my Stampin' Up! Online Store, and all the individual products are linked at the bottom of the post. When you shop online with me in Australia, and use the monthly Host Code, you also qualify for a small thank you gift mid the month after your purchase. My customers love getting these little gifts in the mail. Here's the shop link (individual product links at the end of the post), and this month's host code (if it's past October when you are reading this, this month's code is in the right hand column or HERE). You can read about three ways to shop with me HERE.

Shop Online

October Host Code

Thanks for checking in today. Hope to see you back here soon,

Claire

 

Product List

Comments

Feed You can follow this conversation by subscribing to the comment feed for this post.

Just gorgeous, Claire. I love it.
The colours are so beautiful together.

I really love your gift card holder Claire, and the colours you chose ❤️

Very nice gift card holder. The colors are just gorgeous. Thanks for sharing

Claire,
This gift card holder is absolutely Gorgeous, thank you so much for sharing with us.
Happy Holidays to you and yours!
Dawn

Holy cow!! I love love love 💕 this.

This is one of the loveliest gift card holders I have seen...and I don't usually like gray but LOVE this colour combo! nice work!

What a beautiful idea.

The comments to this entry are closed.